Raven SmarTrax Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 59

background image

CHAPTER

1

Manual No. 016-5034-004

1

Chapter 1

Important Safety

Information

Read this manual and the operation and safety instructions included with your implement and/or controller
carefully before installing the SmarTrax™ system.

•

Follow all safety information presented within this manual.

•

If you require assistance with any portion of the installation or service of your Raven equipment, contact
your local Raven dealer for support.

•

Follow all safety labels affixed to the SmarTrax system components. Be sure to keep safety labels in good
condition and replace any missing or damaged labels. To obtain replacements for missing or damaged
safety labels, contact your local Raven dealer.

When operating the machine after installing SmarTrax, observe the following safety measures:

•

Be alert and aware of surroundings.

•

Do not operate SmarTrax or any agricultural equipment while under the influence of alcohol or an illegal
substance.

•

Remain in the operator’s position in the machine at all times when SmarTrax is engaged.

•

Disable SmarTrax when exiting the operator’s seat and machine.

•

Do not drive the machine with SmarTrax enabled on any public road.

•

Determine and remain a safe working distance from other individuals. The operator is responsible for
disabling SmarTrax when the safe working distance has diminished.

•

Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine.

•

When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in
case a hose has not been properly tightened.

•

The machine must remain stationary and switched off during SmarTrax installation or maintenance.

NOTICE

WARNING

«
...
3
4
5
6
7
...
»

Содержание SmarTrax




























































Отзывы:

Нет отзывов

Похожие инструкции для SmarTrax

Бренд: Rain Bird Страницы: 48

Бренд: ZETRON Страницы: 3

VLT AQUA Drive FC 202

Бренд: Danfoss Страницы: 124

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 114

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 8

ECL Comfort 296

Бренд: Danfoss Страницы: 159

VLT AutomationDrive FC 301

Бренд: Danfoss Страницы: 78

Бренд: Danfoss Страницы: 20

ECL Comfort 210

Бренд: Danfoss Страницы: 12

ECL Comfort 110

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 64

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды