Raven SmarTrax Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 59

background image

Chapter 4

32

John Deere 7X00/7X10 Series SmarTrax™ Installation Manual

FIGURE 14.

Sensor Centering Bracket Installed

4.

Slide the sensor centering bracket tight against the kingpin bolt as shown in Figure 14 above.

Note:

The bracket should be positioned so that the slot is in line with the front axle.

5.

Fully tighten the kingpin bolt, ensuring the bracket stays aligned with the axle and tight against the kingpin
bolt.

FIGURE 15.

WAS Coupler Installed

6.

Install the WAS coupler (P/N 307-0159-419) in the rectangular cutout of the sensor centering bracket.

Note:

The flat side of the ‘D’ profile should be closest to the machine’s engine.

FIGURE 16.

Rotary Sensor Installed on Sensor Bracket

Flat Face of ‘D’
Profile

Sensor
Connector

Bracket
Base

«
...
34
35
36
37
38
...
»

Содержание SmarTrax




























































Отзывы:

Нет отзывов

Похожие инструкции для SmarTrax

Бренд: OmarLift Страницы: 14

Бренд: ECKELMANN Страницы: 178

Бренд: Yealink Страницы: 6

MeetingSpace VC800

Бренд: Yealink Страницы: 6

Бренд: Yealink Страницы: 16

Бренд: Yealink Страницы: 299

VC210 Teams Edition

Бренд: Yealink Страницы: 12

Бренд: Yealink Страницы: 16

Бренд: Yealink Страницы: 30

MeetingSpace VC200

Бренд: Yealink Страницы: 8

MVC Series: MVC800

Бренд: Yealink Страницы: 16

Бренд: Yealink Страницы: 8

Бренд: Yealink Страницы: 16

Бренд: York Страницы: 24

Бренд: brel-motors Страницы: 2

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

Бренд: Aulisa Страницы: 32

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды