Raven SmarTrax Скачать руководство пользователя страница 22

Страница: 22 / 59

Chapter 3

John Deere 7X00/7X10 Series SmarTrax™ Installation Manual

Install the Pressure Hose

Note:

Loosely install the connections to the machine’s hydraulic valve. Do not tighten the connections
until instructed to do so.

FIGURE 7.

Pressure Hose Installed

Locate and disconnect the pressure hose from the machine’s hydraulic valve, located at the back of the
tractor.

Install a -8 ORFS M/M/F swivel run tee adapter fitting (P/N 333-0012-028) in the open pressure port.

Connect the machine’s pressure hose to the opposite end of the installed tee fitting.

Install the straight end of the supplied hydraulic hose (P/N 214-1000-760) on the 90° end of the installed tee
fitting.

Label the straight end of the installed hydraulic hose with a “P.”

Note:

The installed hydraulic hose will be connected to the SmarTrax valve (P/N 334-0003-088) later in
the installation procedure.

Route the installed hydraulic hose to the installed universal bracket (P/N 107-0171-578) mounting location.

Install the Tank Hose

Note:

Loosely install the connections to the machine’s hydraulic valve. Do not tighten the connections
until instructed to do so.

Machine’s
Pressure
Hose

P/N 333-0012-028

P/N 214-1000-760

Содержание SmarTrax



























































Результаты поиска

Содержание SmarTrax

Отзывы:

Похожие инструкции для SmarTrax

Бренды по названию

Популярные бренды

Raven SmarTrax, Руководство по установке

Результаты поиска

Содержание SmarTrax

Отзывы:

Похожие инструкции для SmarTrax

Бренды по названию

Популярные бренды