Raven SmarTrax Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 59

background image

Chapter 3

14

John Deere 7X00/7X10 Series SmarTrax™ Installation Manual

Install Fittings in the SmarTrax Valve

Before mounting the SmarTrax valve (P/N 334-0003-088) on the machine, install the proper fittings in the
valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure.

FIGURE 1.

Fittings Installed in the SmarTrax Valve

NOTICE

The appearance of the SmarTrax hydraulic
valve may vary slightly from the images
contained in this manual. However, the fittings,
hose connections, and cable connections
remain the same.

Fitting

Part Number

Port

Fitting - -4 ORFS (M) to -6 SAE O-Ring (M) Straight Adapter

333-0012-195

LSPV,

LS STEER

Fitting - -4 ORFS M/F 90° Swivel Elbow

333-0012-023

LS STEER

Fitting - -6 ORFS (M) to -8 SAE O-Ring (M) Straight Adapter

333-0012-199

P, T

Fitting - -6 ORFS (M) to -10 SAE O-Ring (M) Straight Adapter

333-0012-233

A, B

Transducer - 0-3000 PSI Pressure

422-0000-086

PS

Install 90° Swivel Elbow
(P/N 333-0012-023) on
This Fitting

«
...
16
17
18
19
20
...
»

Содержание SmarTrax




























































Отзывы:

Нет отзывов

Похожие инструкции для SmarTrax

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: ABATEC Страницы: 8

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: CALEFFI Страницы: 12

QuickSetter+ 132 Series

Бренд: CALEFFI Страницы: 5

Бренд: Datalogic Страницы: 15

Бренд: VAT Страницы: 27

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

Бренд: Watlow Страницы: 4

Бренд: Polycom Страницы: 2

Cutler-Hammer LMR

Бренд: Eaton Страницы: 38

Бренд: LAB-EL Страницы: 25

Бренд: Cardigo Страницы: 12

Бренд: Daikin Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды