manualshive.com logo in svg

Raven SmarTrax, Руководство по установке, Страница: 50 / 59

Поделиться
Скачать
Raven SmarTrax Скачать руководство пользователя страница 50

Chapter 5

46

John Deere 7X00/7X10 Series SmarTrax™ Installation Manual

Install the Chassis Cable - SmarTrax-Only 

Systems (If Applicable)

If the machine does not contain an existing chassis power system (such as AutoBoom, product control, etc.), it 
is necessary to install the chassis power cable to operate the SmarTrax system. If a CAN system already exists 
on the machine, refer to 

Connect SmarTrax to an Existing Chassis Cable (If Applicable)

 below to connect 

power to the SmarTrax system.

Note:

The chassis cable is sold separately. Contact your local Raven dealer for ordering information.

1.

Locate the SmarTrax chassis cable (P/N 115-4001-085).

2.

Connect the TO SMARTRAX NODE connector from the chassis cable to the round 16-pin connector on the 
node harness (P/N 115-4001-109).

3.

Connect the TO CONSOLE CABLE connector to the Raven console cable.

4.

Install a terminator (P/N 063-0172-369) on the CAN cable connector.

5.

Loop and tie-off the REMOTE SWITCH cable connection, securing it with plastic cable ties as necessary.

Note:

The REMOTE SWITCH connector is not used in the SmarTrax system. Ensure the cable is 
secured away from moving parts and heat sources.

6.

Connect the ring terminals to the battery.

Note:

The positive connectors are fused.

Connect SmarTrax to an Existing Chassis 

Cable (If Applicable)

Note:

The SmarTrax interface tee is sold separately. Contact your local Raven dealer for ordering 
information.

1.

Locate and disconnect the connection between the Raven console cable and chassis cable on the 
machine’s existing CAN system.

2.

Install the SmarTrax interface tee cable (P/N 115-4001-070 or 115-4001-071) between the chassis and 
Raven console harness.

3.

Connect the SmarTrax node cable (P/N 115-4001-109) to the remaining SmarTrax interface tee.

Содержание SmarTrax




























































Отзывы:

Нет отзывов