Raven SmarTrax Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 59

background image

5

Manual No. 016-5034-004

43

Cab Component Installation

1.

Install the two large, rectangular connectors of the node harness (P/N 115-4001-109) into the correct ports
of the node.

2.

Tighten the bolts on the harness connectors to secure the connections.

3.

Locate the ENABLE connector and connect it to the foot switch cable connector.

Install the Valve Harness

FIGURE 8.

Valve Harness Connected to Node Harness

1.

Connect the CHASSIS connector of the valve harness (P/N 115-4001-093) to the green mating connector
of the node harness (P/N 115-4001-109).

FIGURE 9.

Valve Harness Routed Outside the Cab

2.

Route the valve harness through the opening in the right-rear window of the cab.

3.

Connect the TRANSDUCER connector to the pressure transducer (P/N 422-0000-086) installed in Port PS
of the SmarTrax valve (P/N 334-0003-088).

4.

Connect the VALVE connector to the open PVE port of the SmarTrax valve.

VALVE
Connection

TRANSDUCER
Connection

Valve Harness
Routed Outside
the Cab

«
...
45
46
47
48
49
...
»

Содержание SmarTrax




























































Отзывы:

Нет отзывов

Похожие инструкции для SmarTrax

Бренд: ABB Страницы: 52

Бренд: Nelson Страницы: 19

Бренд: C-TEC Страницы: 2

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Daktronics Страницы: 5

Бренд: Daikin Страницы: 12

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: Rain Bird Страницы: 138

Бренд: Saluki Страницы: 13

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

Бренд: S&C Страницы: 26

Бренд: Barton Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды