Rational CombiMaster Plus CM Скачать руководство пользователя страница 24

Страница: 24 / 91

V08 en, SCC

- 24 -

CM_P Index I/ CM Index I

CM 61 - 101

The basic model CM with index I has the identical construction as CM_P index H. It is only available in size 61 and

101 (without Cleanjet) and only with right hinged door.

CM_P with CleanJet

PCB

All CM_P with index I have a new PCB 42.00.272

Hand shower:

All CM and CM_P with index I get a new hand shower roll guide

(56.00.061).

Door:

All CM_P units 60 - 202 are equipped with a new door with 2 glass panes and halogen light

inside the cabinet. (without LED light, only halogen light in the cabinet

Only the CM_P XS (60) has a LED light in the door like SCC_XS (without level indication, without halogen light).

CM_P XS:

In order to connect the unit to the drinking water supply, water protection according EN 1717 must be ensured by

installing a double check valve, a type CA system divider or similar in the fresh water line.

Additional function

CALC - Descaling steam generator

Caution!

Descaler shall ONLY be filled through the steam inlet port inside the interior cabinet!

Protective clothing must be worn.

Interior cabinet temperature must be below 40°C (104°F);

Steam generator will be emptied, refilled and emptied again;

„CALC“ „FILL“: prompt to fill descaler into the steam generator;

30 second waiting time (to rinse cabinet with water);

“door”: prompt to close cabinet door;

45 minutes reaction time for the chemical,

“CALC”: Steam generator will be rinsed twice and refilled again;

Steam mode for 15 minutes

“END” and buzzer for 20 seconds

Display:

Call service partner to descale steam generator

Содержание CombiMaster Plus CM




























































































Результаты поиска

Содержание CombiMaster Plus CM

Отзывы:

Похожие инструкции для CombiMaster Plus CM

Бренды по названию

Популярные бренды

Rational CombiMaster Plus CM, Руководство по обучению

Результаты поиска

Содержание CombiMaster Plus CM

Отзывы:

Похожие инструкции для CombiMaster Plus CM

Бренды по названию

Популярные бренды