RAM 2010 Truck Diesel Supplement страница 67 Скачать руководство пользователя | Manualshive

Страница: 67 / 147

background image

ADDING FUEL

CAUTION!

To avoid fuel spillage and overfilling, do not “top
off” the fuel tank after filling.

NOTE:

•

When the fuel nozzle “clicks” or shuts off, the fuel
tank is full.

•

Tighten the fuel filler cap until you hear a “clicking”
sound. This is an indication that the fuel filler cap is
properly tightened.

•

Make sure that the fuel filler cap is tightened each time
the vehicle is refueled.

WARNING!

A fire may result if fuel is pumped into a portable
container that is on a truck bed. You could be burned.
Always place fuel containers on the ground while
filling.

Fuel Filler Cap

If the fuel filler cap is lost or damaged, be sure the
replacement cap is for use with this vehicle.

CAUTION!

Damage to the fuel system or emission control sys-
tem could result from using an improper fuel tank
filler tube cap. A poorly fitting cap could let impuri-
ties into the fuel system.

66

STARTING AND OPERATING

«
...
65
66
67
68
69
...
»

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Truck Diesel Supplement

Бренд: Cadillac Страницы: 20

Бренд: BURY Страницы: 2

Бренд: Guidosimplex Страницы: 8

Бренд: NavLinkz Страницы: 23

Бренд: Xpresskit Страницы: 12

Performer-Plus 2172

Бренд: Edelbrock Страницы: 4

Бренд: Volkswagen Zubehör Страницы: 133

Directechs FORD11

Бренд: Directed Страницы: 23

Бренд: Chevrolet Страницы: 55

Бренд: Prorack Страницы: 14

BEDXTENDER HD 74805-00A

Бренд: AMP Research Страницы: 7

Бренд: Volkswagen Страницы: 83

Бренд: Kia Страницы: 13

Бренд: Kia Страницы: 54

Бренд: Oldsmobile Страницы: 410

Бренд: Sune Technology Страницы: 24

Бренд: achilles Страницы: 18

Бренд: Mercedes-Benz Страницы: 381

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды