RAM 2010 Truck Diesel Supplement Скачать руководство пользователя | Manualshive

Страница: 51 / 147

background image

•

transmission

has

reached

normal

operating

temperature.

NOTE:

If the vehicle is started in extremely cold tem-

peratures, the transmission may not shift into Overdrive
and will automatically select the most desirable gear for
operation at this temperature. Normal operation will
resume when the transmission fluid temperature has
risen to a suitable level. Refer to the “Note” under
“Torque Converter Clutch” later in this section.

If the transmission temperature gets extremely hot, the
transmission will automatically select the most desirable
gear for operation at this temperature. If the transmission
temperature becomes hot enough the “Transmission
Temperature Warning Light” may illuminate and the
transmission may downshift out of Overdrive until the
transmission cools down. After cool down, the transmis-
sion will resume normal operation.

The transmission will downshift from Overdrive to
DRIVE if the accelerator pedal is fully pressed at vehicle
speeds above approximately 35 mph (56 km/h).

When To Use TOW/HAUL

When driving in hilly areas, towing a trailer, carrying a
heavy load, etc., and frequent transmission shifting oc-
curs, press the “TOW/HAUL” switch once to select
TOW/HAUL. In TOW/HAUL mode, fourth to fifth gear
upshifts are delayed. Shifts into fifth and sixth gear are
still allowed under steady cruise conditions. Closed
throttle downshifts (for improved engine braking) may
occur during steady braking maneuvers. Pressing the
switch a second time restores normal operation. Normal
operation is always the default at engine start-up.

50

STARTING AND OPERATING

«
...
49
50
51
52
53
...
»

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Truck Diesel Supplement

Бренд: iDataLink Страницы: 9

Бренд: kaarta Страницы: 29

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: RAM Commercial Страницы: 12

Бренд: Prorack Страницы: 14

Бренд: FAAFTECH Страницы: 8

Бренд: AutoMaxi Страницы: 2

2016 Sandero Stepway

Бренд: Renault Страницы: 183

Бренд: EZTRUNK Страницы: 3

Бренд: PAC Страницы: 14

Бренд: Kolpin Страницы: 3

Бренд: Lexus Страницы: 34

Бренд: Toyota Страницы: 32

Бренд: Havis Страницы: 5

Бренд: Subaru Страницы: 19

Бренд: POOL-LINE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды