RAM 2010 Truck Diesel Supplement страница 42 Скачать руководство пользователя

Страница: 42 / 147

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms engine coolant and
permits quicker starts in cold weather. Connect the heater
cord to a ground-fault interrupter protected 110–115 Volt
AC electrical outlet with a grounded, three-wire exten-
sion cord.

The engine block heater cord is routed under the hood to
the right side and can be located just behind the grille
near the headlamp.

NOTE:

The engine block heater cord is a factory in-

stalled option. If your vehicle is not equipped, heater
cords are available from your authorized MOPAR

威

dealer.

The block heater must be plugged in at least one hour to
have an adequate warming effect on the coolant.

WARNING!

Remember to disconnect the cord before driving.
Damage to the 110–115 Volt electrical cord could
cause electrocution.

NOTE:

The block heater will require 110 Volts AC and

6.5 Amps to activate the heater element.

Block Heater Usage

For ambient temperatures below 0°F (-18°C), engine
block heater usage is recommended.

For ambient temperatures below –20°F (-29°C), engine
block heater usage is required.

STARTING AND OPERATING

Содержание 2010 Truck Diesel Supplement




















































































































































Результаты поиска

Содержание 2010 Truck Diesel Supplement

Отзывы:

Похожие инструкции для 2010 Truck Diesel Supplement

Бренды по названию

Популярные бренды

RAM 2010 Truck Diesel Supplement, Руководство пользователя

Результаты поиска

Содержание 2010 Truck Diesel Supplement

Отзывы:

Похожие инструкции для 2010 Truck Diesel Supplement

Бренды по названию

Популярные бренды