RAM 2010 Truck Diesel Supplement Скачать руководство пользователя | Manualshive

Страница: 129 / 147

background image

90,000 Miles (144,000 km) or 72 Months Maintenance Service Schedule

❏

When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator
System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no
circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.

❏

Rotate tires.

❏

Inspect drive belt, replace as required.

❏

Replace fuel filter element.

❏

Lubricate front drive shaft fitting (4x4).

❏

Lubricate outer tie rod ends.

❏

Inspect the wheel bearings.

❏

Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;
replace if necessary.

❏

Inspect brake linings.

❏

Inspect and adjust parking brake if necessary.

❏

Inspect the front (4x4) and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.

❏

Check the transfer case fluid (4x4).

❏

Change automatic transmission fluid (Chassis Cab Only).

Odometer Reading

Date

Repair Order #

Dealer Code

Signature Authorized Chrysler Dealer

128

MAINTENANCE SCHEDULES

«
...
127
128
129
130
131
...
»

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Truck Diesel Supplement

Бренд: Triumph Страницы: 86

2011 Corolla LE

Бренд: Toyota Страницы: 19

Бренд: Carax Страницы: 2

MagicWatch MWE800

Бренд: Waeco Страницы: 212

Chevrolet Silverado 2500HD 2021

Бренд: GMC Страницы: 433

Бренд: Cadillac Страницы: 368

Бренд: Luverne Страницы: 3

Бренд: Navman Страницы: 27

Бренд: NavLinkz Страницы: 21

Бренд: Veldo Teknoloji Страницы: 32

Бренд: Horn Tools Страницы: 12

Бренд: Honda Страницы: 24

Бренд: Toyota Страницы: 295

Бренд: Revelation Страницы: 4

WG Grand Cherokee 2002

Бренд: Jeep Страницы: 74

Бренд: Kargo Master Страницы: 8

Бренд: Chevrolet Страницы: 6

Бренд: Fcar Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды