RAM 2010 Truck Diesel Supplement Скачать руководство пользователя | Manualshive

Страница: 38 / 147

background image

NOTE:

For EVIC messages related to the vehicle’s

exhaust system, refer to “Maintenance Procedures/
Intervention Regeneration Strategy – EVIC Message Pro-
cess Flow” in “Maintaining Your Vehicle” for further
information.

Idle-Up Feature – Automatic Transmission Only

The driver-controlled high idle speed feature will help
increase cylinder temperatures and provide additional
cab heat, however, excessive idling may still cause the
exhaust aftertreatment system to not properly regenerate.
Extended periods of idle time should be avoided.

The Idle-Up feature uses the speed control switches to
increase engine idle speed and quickly warm the vehi-
cle’s interior.

1. With the transmission in PARK, the parking brake
applied, and the engine running, press the speed control
switch to the ON position, then press the SET switch.

2. The engine RPM will go up to 1100 RPM. To increase
the RPM, press and hold the ACCEL/RESUME switch
and the idle speed will increase to approximately 1500
RPM. To decrease the RPM, press and hold the DECEL
switch and the idle speed will decrease to approximately
1100 RPM.

3. To cancel the Idle–Up feature, either press the CAN-
CEL switch, press the ON/OFF switch, or press the brake
pedal.

Stopping The Engine

Idle the engine a few minutes before routine shutdown.
After full load operation, idle the engine three to five
minutes before shutting it down. This idle period will
allow the lubricating oil and coolant to carry excess heat
away from the combustion chamber, bearings, internal
components, and turbocharger. This is especially impor-
tant for turbocharged, charge air-cooled engines.

4

STARTING AND OPERATING

37

«
...
36
37
38
39
40
...
»

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Truck Diesel Supplement

Бренд: Saab Страницы: 445

Бренд: Xhorse Страницы: 48

Бренд: Lexus Страницы: 34

Бренд: Toyota Страницы: 32

Бренд: Black Horse Off Road Страницы: 7

Бренд: Huf Страницы: 6

MagicSpeed MS900

Бренд: Waeco Страницы: 120

Бренд: BMW Страницы: 64

Бренд: Flash Cover Страницы: 2

Бренд: MBW Страницы: 40

PRIME DESIGN UXV 211

Бренд: Safe Fleet Страницы: 8

Бренд: 3SIXT Страницы: 4

Бренд: Hamron Страницы: 6

Бренд: Camcar Страницы: 2

Бренд: TOP VEHICLE TECH Страницы: 8

Бренд: HG2 Страницы: 6

Бренд: PROUSER Страницы: 40

Бренд: Hotchkis Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды