RAM 2010 Truck Diesel Supplement страница 125 Скачать руководство пользователя | Manualshive

Страница: 125 / 147

background image

60,000 Miles (96,000 km) or 48 Months Maintenance Service Schedule

❏

When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator
System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no
circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.

❏

Rotate tires.

❏

Replace fuel filter element.

❏

Lubricate front drive shaft fitting (4x4).

❏

Lubricate outer tie rod ends.

❏

Inspect the wheel bearings.

❏

Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;
replace if necessary.

❏

Inspect the front (4x4) and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.

❏

Change automatic transmission fluid and sump filter (Chassis Cab Only).

❏

Change automatic transmission fluid and filter(s) if using your vehicle for any of the following: police, fleet, or frequent trailer towing (Ram
Truck Only).

❏

Inspect the manual transmission fluid, add if necessary.

❏

Change the transfer case fluid (4x4).

Odometer Reading

Date

Repair Order #

Dealer Code

Signature Authorized Chrysler Dealer

124

MAINTENANCE SCHEDULES

«
...
123
124
125
126
127
...
»

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Truck Diesel Supplement

Бренд: Yakima Страницы: 8

Бренд: Porsche Страницы: 192

Бренд: Axxess Страницы: 8

Бренд: hc-cargo Страницы: 60

Бренд: Voxoa Страницы: 48

Бренд: Jeep Страницы: 374

Бренд: Buick Страницы: 161

Бренд: Lexus Страницы: 6

Бренд: Magneti Marelli Страницы: 3

Бренд: Curt Group Страницы: 2

Бренд: Metra Electronics Страницы: 8

Gigaware 12-493

Бренд: Gigaware Страницы: 8

Бренд: AA Products Страницы: 8

Бренд: Whispbar Страницы: 15

Бренд: Buick Страницы: 20

2013 Duramax Diesel

Бренд: Chevrolet Страницы: 132

2012 CIVIC SEDAN HF

Бренд: Honda Страницы: 8

Бренд: LG Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды