RAM 2010 Truck Diesel Supplement Скачать руководство пользователя | Manualshive

Страница: 108 / 147

background image

•

EXHAUST SYSTEM

− Removal or rendering inoperative exhaust system

components including the muffler or tailpipe.

•

ENGINE COOLING SYSTEM

− Removal or rendering inoperative the fan clutch.

− Removal of the fan shroud.

Noise Emission Warranty

The manufacturer warrants that this vehicle as manufac-
tured by the manufacturer, was designed, built and
equipped to conform at the time it left the manufacturer’s

control with all applicable U.S. EPA Noise Control Regu-
lations.

This warranty covers this vehicle as designed, built and
equipped by the manufacturer, and is not limited to any
particular part, component or system of the vehicle
manufactured by the manufacturer. Defects in design,
assembly or in any part, component or system of the
vehicle as manufactured by the manufacturer, which, at
the time it left the manufacturer’s control, caused noise
emissions to exceed Federal standards, are covered by
this warranty for the life of the vehicle.

6

MAINTAINING YOUR VEHICLE

107

«
...
106
107
108
109
110
...
»

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Truck Diesel Supplement

Бренд: Happy Orange Страницы: 2

Бренд: Taffio Страницы: 8

Transit Vancouver Wagon

Бренд: Webasto Страницы: 44

Бренд: EEZ RV Страницы: 31

Бренд: RAM Страницы: 616

Бренд: Nav TV Страницы: 9

Бренд: Honda Страницы: 81

Бренд: Cadillac Страницы: 368

Бренд: Luverne Страницы: 3

Бренд: Navman Страницы: 27

Бренд: Opel Страницы: 32

Бренд: Hudson Страницы: 34

Бренд: E&G Classics Страницы: 3

1966 Spider 105

Бренд: Alfa Romeo Страницы: 46

Бренд: BraunAbility Страницы: 46

Бренд: Z Flash Страницы: 4

Бренд: Poison Spyder Страницы: 5

Бренд: Kolpin Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды