manualshive.com logo in svg

RAM 2010 Truck Diesel Supplement, Руководство пользователя

Поделиться
Скачать
RAM 2010 Truck Diesel Supplement Скачать руководство пользователя страница 137

150,000 Miles (240,000 km) or 120 Months Maintenance Service Schedule

❏

When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator
System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no
circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.

❏

Rotate tires.

❏

Replace fuel filter element.

❏

Inspect drive belt, replace as required.

❏

Adjust valve lash clearance.

❏

Lubricate front drive shaft fitting (4x4).

❏

Lubricate outer tie rod ends.

❏

Inspect the wheel bearings.

❏

Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;
replace if necessary.

❏

Flush and replace engine coolant at 120 months, if not replaced at 97,500 miles (157 000 km).

❏

Inspect the front (4x4) and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.

❏

Check the transfer case fluid (4x4).

❏

Change automatic transmission fluid (Chassis Cab Only).

Odometer Reading

Date

Repair Order #

Dealer Code

Signature Authorized Chrysler Dealer

136

MAINTENANCE SCHEDULES

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды