RAM 2010 Truck Diesel Supplement страница 127 Скачать руководство пользователя | Manualshive

Страница: 127 / 147

background image

75,000 Miles (120,000 km) or 60 Months Maintenance Service Schedule

❏

When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator
System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no
circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.

❏

Rotate tires.

❏

Flush and replace engine coolant at 60 months, if not replaced at 97,500 miles (157 000 km).

❏

Inspect drive belt, replace as necessary.

❏

Replace fuel filter element.

❏

Lubricate front drive shaft fitting (4x4).

❏

Lubricate outer tie rod ends.

❏

Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;
replace if necessary.

❏

Inspect the front (4x4) and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.

Odometer Reading

Date

Repair Order #

Dealer Code

Signature Authorized Chrysler Dealer

126

MAINTENANCE SCHEDULES

«
...
125
126
127
128
129
...
»

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Truck Diesel Supplement

Green Motion Building

Бренд: Eaton Страницы: 12

Бренд: Alpine Страницы: 2

Бренд: Whispbar Страницы: 15

Бренд: Alpine Страницы: 69

Бренд: Allen Sports Страницы: 2

YARIS LIFTBACK 2009

Бренд: Toyota Страницы: 13

Бренд: Westfalia Страницы: 71

Green Motion DC 66

Бренд: Eaton Страницы: 18

Бренд: Mercedes-Benz Страницы: 368

Бренд: walser Страницы: 24

Бренд: Metra Electronics Страницы: 2

Бренд: Kia Страницы: 11

Бренд: Saab Страницы: 426

Бренд: Ranger design Страницы: 24

51 47 0 027 792

Бренд: BMW Страницы: 7

Бренд: Ford Страницы: 728

Бренд: Westin Страницы: 5

Бренд: Honda Страницы: 253

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды