RAM 2010 Truck Diesel Supplement страница 55 Скачать руководство пользователя | Manualshive

Страница: 55 / 147

background image

DRIVE

This range provides all forward gears, including fourth
gear direct and fifth or sixth (if equipped) gear overdrive
(refer to “Overdrive Operation” in this section). Use this
range for most city and highway driving.

THIRD

This range should be used for driving in slight heavy city
traffic or on mountain roads where more precise speed
control is desirable. Use it when climbing long grades,
and for engine braking when descending moderately
steep grades. To prevent excessive engine speed do not
exceed 40 mph (64 km/h) in this range.

SECOND

This range should be used for driving in more severe
conditions and lower speeds than THIRD. To prevent
excessive engine speed do not exceed 25 mph (40 km/h)
in this range.

FIRST

This range should be used for driving up very steep hills
and for engine braking at low speeds 12 mph (19 km/h)
or less when going downhill. To prevent excessive engine
speed, do not exceed 12 mph (19 km/h) in this range.

NOTE:

Use caution when operating a heavily loaded

vehicle in SECOND or FIRST gear selections in high
ambients as torque converter slip can impose significant
additional heat load on the cooling system.

Overdrive Operation

The Overdrive automatic transmission contains an elec-
tronically controlled fifth and sixth (if equipped) speed
(Overdrive). The transmission will automatically shift
from DRIVE to Overdrive if the following conditions are
present:

•

the shift lever is in DRIVE;

54

STARTING AND OPERATING

«
...
53
54
55
56
57
...
»

Содержание 2010 Truck Diesel Supplement




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Truck Diesel Supplement

Бренд: Paxton Automotive Страницы: 85

Бренд: Thule Страницы: 8

Бренд: Thule Страницы: 12

Бренд: Rati Страницы: 2

Бренд: TATA Motors Страницы: 92

Бренд: Meta System Страницы: 22

Бренд: Acura Страницы: 6

Бренд: Mont Blanc Страницы: 2

84 61 0 028 926

Бренд: BMW Страницы: 13

Бренд: Roadtrek Страницы: 61

Бренд: Connects2 Страницы: 8

Бренд: ideus Страницы: 116

Бренд: FIRRAK Страницы: 12

Бренд: CITROEN Страницы: 86

QuadraTop Adventure Top S

Бренд: Quadratec Страницы: 13

Бренд: XPENG Страницы: 316

2011 odyssey EX-L

Бренд: Honda Страницы: 722

Бренд: Hotchkis Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды