Rally URCap Скачать руководство пользователя

Страница: 112 / 117

combination with

user-defined path

)

rf_blend

Blend radius in linear
movements as a
fraction of the distance
between subsequent
waypoints.

Default: 0.3
Recommended values: 0 - 0.3

rf_safe_reach

Workaround for a UR
bug where the inverse
kinematics calculations
may throw an
exception

Default: 0.01

rf_use_movej

The robot uses joint
move (movej) to
approach the pick
position.
Use this option when
experiencing "Joint
position close to limits"
due to wrist 3 winding
up during palletizing.

Default: True

rf_cpuidle_ticks

Threshold value for
inserting idle
instructions to avoid
"Runtime is too much
behind" and "Lost
communication with
controller" issues.

Default: 20 on E-series
Default: 100000 on CB-series
Has no effect on CB 3.0

rf_cpuidle_l

Increment for the idle
tick counter, variant 1

Default: 2 on E-series
Default: 1 on CB-series
Has no effect on CB 3.0

rf_cpuidle_xl

Increment for the idle
tick counter, variant 2

Default: 4 on E-series
Default: 1 on CB-series
Has no effect on CB 3.0

rf_cpuidle_xxl

Increment for the idle
tick counter, variant 3

Default: 25 on E-series
Default: 20000 on CB-series
Has no effect on CB 3.0

rf_ur_wd_timeout

Workaround for a UR
bug where a move
command never
terminates

Default: 60 (seconds)

Version 2.9.1

112

Содержание URCap



















































































































Результаты поиска

Содержание URCap

Отзывы:

Похожие инструкции для URCap

Бренды по названию

Популярные бренды

Rally URCap, Руководство пользователя

Результаты поиска

Содержание URCap

Отзывы:

Похожие инструкции для URCap

Бренды по названию

Популярные бренды