Rally URCap Скачать руководство пользователя | Manualshive

Страница: 26 / 117

background image

5 - Physical Installation - Best Practice

5.1 - Robot installation

5.1.1 - Check joint positions first

The UR10 joints have a l-360 degrees position range, so it is essential to check
whether the joint positions are not too close to their limits, before attaching the vacuum hose
and other objects (

figure 16

). Having a bad initial position may cause the robot to stop with

Joint position close to the limit

during palletizing.

Note:

The robot can be operated as "left-handed" or "right-handed". Left handed or right

handed implies on which side the shoulder joint is located, seen from the opposite side of
the conveyor. For a right handed robot, the shoulder joint is located to the right side of the
base joint. For a left handed robot, the shoulder joint is located to the left of the base joint.
The examples in this document are made with a left-handed configuration.

Figure 16

: Check the joint positions before mounting vacuum hoses and cables.

5.1.2 - Robot position on the base column

Before mounting the robot on the base column, make sure that the power connector on the
robot arm points behind the palletizer cell, see

figure 17

. This is not mandatory, but

recommended for best reachability both on the left and right pallet positions.

Version 2.9.1

© Rocketfarm AS 2021. All rights reserved.

26

«
...
24
25
26
27
28
...
»

Содержание URCap






















































































































Отзывы:

Нет отзывов

Похожие инструкции для URCap

Бренд: Stiga Страницы: 29

Бренд: evoheat Страницы: 20

AquaForce 30XQ0330

Бренд: Carrier Страницы: 49

Бренд: Cobra Страницы: 11

Бренд: Tanaka Страницы: 5

Бренд: Samsung Страницы: 44

AG010KSV Series

Бренд: Samsung Страницы: 86

AG042KSV Series

Бренд: Samsung Страницы: 90

Бренд: Nordcap Страницы: 88

Бренд: Bisonte Страницы: 119

Бренд: Go-On Страницы: 28

Бренд: Nakayama Страницы: 40

Бренд: Echo Страницы: 44

Бренд: teca Страницы: 7

Бренд: teca Страницы: 10

Бренд: Electrolux Страницы: 10

Бренд: Electrolux Страницы: 8

Бренд: Electrolux Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды