Quectel 5G Module Series Скачать руководство пользователя

Страница: 30 / 86

5G Module Series

RM500Q-GL Hardware Design

RM500Q-GL_Hardware_Design 29 / 85

To avoid damages to the internal flash, DON'T cut off the power supply before the module is completely

turned off by pulling down FULL_CARD_POWER_OFF# pin for more than 7 s, and DON'T cut off power

supply directly when the module is working.

3.3.3. Monitor the Power Supply

AT+CBC

command can be used to monitor the voltage value of VCC. For more details, see

document [4].

3.4. Turn on

FULL_CARD_POWER_OFF# (abbreviated as

“FCPO#” in this document) is used to turn on/off the

module. When the input signal is asserted HIGH (

≥ 1.19 V), the module will turn on.

This input signal is 3.3 V tolerant and can be driven by either 1.8 V or 3.3 V GPIO. And it has internally

pulled down

with a 100 kΩ resistor.

The following table shows the definition of FULL_CARD_POWER_OFF#.

Table 8: Definition of FCPO#

Pin No. Pin Name

I/O

Description

DC Characteristics Comment

FULL_CARD_

POWER_OFF#

DI, PD

Turn on/off the module.

High level: Turn on

Low level: Turn off

max = 4.4 V

min = 1.19 V

max = 0.2 V

Pull down with a

100 k

Ω resistor

NOTE

Содержание 5G Module Series























































































Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды

Quectel 5G Module Series, Проектирование аппаратного обеспечения

Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды