Quectel 5G Module Series Скачать руководство пользователя

Страница: 37 / 86

5G Module Series

RM500Q-GL Hardware Design

RM500Q-GL_Hardware_Design 36 / 85

This pin is pulled LOW by default, and will be internally pulled up to 1.8 V by software configuration only

when (U)SIM hot-plug is enabled by

AT+QSIMDET

4.1.2. (U)SIM Hot-plug

The module supports (U)SIM card hot-plug via (U)SIM card hot-plug detection pins (USIM1_DET and

USIM2_DET). (U)SIM card insertion is detected by high/low level. (U)SIM card hot-plug is disabled by

default.

The following command enables (U)SIM card hot-plug function.

USIM1_DET

DI, PU

(U)SIM1 card hot-plug detection.

1.8 V

USIM2_VDD

Power supply for (U)SIM2 card

USIM2_VDD

1.8/3.0 V

USIM2_DATA

DIO, PU

(U)SIM2 card data

USIM2_VDD

1.8/3.0 V

USIM2_CLK

DO, PD

(U)SIM2 card clock

USIM2_VDD

1.8/3.0 V

USIM2_RST

DO, PD

(U)SIM2 card reset

USIM2_VDD

1.8/3.0 V

USIM2_DET

DI, PU

(U)SIM2 card hot-plug detection.

1.8 V

AT+QSIMDET (U)SIM Card Detection

Test Command

AT+QSIMDET=?

Response

+QSIMDET: (

list of supported

<enable>

),(

list of

supported

<insert_level>

)

Read Command

AT+QSIMDET?

Response

+QSIMDET: <enable>,<insert_level>

Write Command

AT+QSIMDET=<enable>,<insert_level>

Response

If there is any error:

ERROR

Maximum Response Time

300 ms

NOTE

Содержание 5G Module Series























































































Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды

Quectel 5G Module Series, Проектирование аппаратного обеспечения

Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды