Quectel 5G Module Series Скачать руководство пользователя

Страница: 52 / 86

5G Module Series

RM500Q-GL Hardware Design

RM500Q-GL_Hardware_Design 51 / 85

4.5.3. WWAN_LED#

WWAN_LED# is used to indicate the RF status of the module, and its sink current is up to 10 mA.

To reduce current consumption of the LED, a current-limited resistor must be placed in series with the

LED, as illustrated by the figure below. The LED is ON when the WWAN_LED# signal is at low level.

Module

WWAN_LED#

PMIC

VCC(Typ. 3.7V)

330

LED1

2, 4
70,72,74

VCC

Figure 25: WWAN_LED# Reference Circuit

The following table shows the RF status indicated by WWAN_LED# signal.

Table 23: Network Status Indications of WWAN_LED#

4.5.4. WAKE_ON_WAN#

The WAKE_ON_WAN# is an open drain pin, which requires a pull-up resistor on the host. When a URC

returns, a one-second low level pulse signal will be outputted to wake up the host.

WWAN_LED# Logic Level

Description

Low (LED on)

RF function is turned on

High (LED off)

RF function is turned off if any of the following occurs:

⚫

The (U)SIM card is not powered.

⚫

W_DISABLE1# is at low voltage level (airplane mode enabled).

⚫

AT+CFUN=4

(RF function disabled).

Содержание 5G Module Series























































































Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды

Quectel 5G Module Series, Проектирование аппаратного обеспечения

Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды