Quectel 5G Module Series Скачать руководство пользователя

Страница: 26 / 86

5G Module Series

RM500Q-GL Hardware Design

RM500Q-GL_Hardware_Design 25 / 85

Run Time

DRX OFF ON OFF

ON OFF ON OFF ON OFF

Figure 3: DRX Run Time and Current Consumption in Sleep Mode

The following part of this section presents the power saving procedure and sleep mode of the module.

If the host supports USB suspend/resume and remote wakeup function, the following two conditions must

be met to make the module enter sleep mode.

⚫

AT+QSCLK=1

command is executed to enable the sleep mode.

⚫

Then the

host’s USB bus, which is connected to the module’s USB interface, enters suspend state.

The following figure shows the connection between the module and the host.

USB Interface

Module

Host

GND

Figure 4: Sleep Mode Application with USB Remote Wakeup

The module and the host will wake up in the following conditions:

⚫

Sending data to module through USB will wake up the module.

⚫

When the module has a URC to report, it will send remote wake-up signals via USB bus to wake up

the host.

Содержание 5G Module Series























































































Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды

Quectel 5G Module Series, Проектирование аппаратного обеспечения

Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды