Qualstar RLS-8350 Скачать руководство пользователя страница 43

Страница: 43 / 140

Store the front hand holds and their mounting screws in a safe location so they
may be re-used if the library is removed from the rack.

With the hand holds removed, slide the library all the way back into the rack
until the flanges on the sides touch the front rack posts.

Install one screw in each rack post

to secure the library to the rack.

(there are 8 potential locations)

Flange

Figure 5-8 The Library fully inserted into the Rack (RLS-85XX shown)

Confirm that the library is housed properly in the rack. The two holes in each of
the flanges should line up with the cage nuts that were installed earlier in the
front rack posts.

Use a Number 2 Phillips screwdriver to install the two screws (one on each side)
that secure the library to the front rack posts.

10.

For RLS-8350 and 85120 libraries follow the procedure described in Section 5.7.5
to reinstall the storage matrices and connect all necessary cables.

11.

For RLS-8560 libraries ONLY follow steps 11 through 23 to install the storage
matrix assembly blank.

5-8

Installation

511000 Rev. F

Содержание RLS-8350













































































































































Результаты поиска

Содержание RLS-8350

Отзывы:

Похожие инструкции для RLS-8350

Бренды по названию

Популярные бренды

Qualstar RLS-8350, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RLS-8350

Отзывы:

Похожие инструкции для RLS-8350

Бренды по названию

Популярные бренды