Qiagen EZ1 Advanced XL Скачать руководство пользователя страница 25

Страница: 25 / 100

EZ1 Advanced XL User Manual 11/2017

Cartridge rack

This rack is located behind the tip rack and holds up to 14 reagent cartridges. Insert the cartridge
rack with the arrow pointing towards the instrument

Cartridge rack.

Reagent cartridges are made of polypropylene, contain prefilled reagents and are available from
QIAGEN.

Reagent cartridges.

A reagent cartridge consists of 10 reagent wells and 2 heating positions. One heating position is
a well, the other is a slot that can accept a tube.

Heating system

The heating system is located under the far end of the cartridge rack. It holds the heating positions
of the reagent cartridges.

Heating positions

Reagent wells

Содержание EZ1 Advanced XL





































































































Результаты поиска

Содержание EZ1 Advanced XL

Отзывы:

Похожие инструкции для EZ1 Advanced XL

Бренды по названию

Популярные бренды

Qiagen EZ1 Advanced XL, Руководство пользователя

Результаты поиска

Содержание EZ1 Advanced XL

Отзывы:

Похожие инструкции для EZ1 Advanced XL

Бренды по названию

Популярные бренды