QED AutoPump AP-2 Скачать руководство пользователя страница 37

Страница: 37 / 111

Page 29

AP-2 Manual

Revision 7 - August, 2007

Chapter 4: Assembly & Installation

STEP 3 -

Tip the top of the pump downwards to about 45°. The float should slide to

the top of the pump and open the air valve. Air should be heard going into

the pump. It will exit the inlet fluid check valve (Bottom-loading) or the

outlet check valve (Top-loading).

Caution:

If air is not acceptable in the fluid discharge hose, disconnect the hose before

performing this test.

STEP 4 -

Tip the head of the pump upwards past horizontal to 45° from the vertical.

The float should slide to the bottom of the pump and close the air valve.

STEP 5 -

Repeat this process 3 or 4 times to ensure the float moves freely and the

air-valve opens and closes. If the pump must be tilted nearly vertical

before the float slide or the air valve moves, open the pump and inspect

for interference.

Pump Support System and Hose Bundling Assembly

A pump support system can be created to support the pump and hoses. The pump support

system uses well caps with various fitting combinations.

(See Figure 11)

Though it is possible in some instances to support a downwell pump with only the tubing, a

separate support line is recommended.

Note:

The walls of some wells deform over time. They may trap a downwell

pump. In some of those cases the support line has proven useful when

retrieving the pump.

In addition to supporting the down-well equipment with a support rope, it may be important

to support down-well hoses (in most cases nylon tubing does not need to be supported by the

support line). Since the down-well hoses can weigh more than the pump, particularly in wells

over 50 feet deep with fluid inside the discharge hose, hose support can avoid problems such

as kinking, jamming, and breaking.

Содержание AutoPump AP-2
















































































































Результаты поиска

Содержание AutoPump AP-2

Отзывы:

Похожие инструкции для AutoPump AP-2

Бренды по названию

Популярные бренды

QED AutoPump AP-2, Руководство по эксплуатации

Результаты поиска

Содержание AutoPump AP-2

Отзывы:

Похожие инструкции для AutoPump AP-2

Бренды по названию

Популярные бренды