QED AutoPump AP-2 Скачать руководство пользователя страница 48

Страница: 48 / 111

QED Environmental Systems

AP-2 Manual

Page 40

Chapter 6: Maintenance

General Maintenance

The AutoPump should be relatively free of maintenance. The frequency of maintenance

depends upon the nature of the fluids being pumped. Follow these general maintenance

checks.

• Periodically inspect all hoses and connections for damage. Make sure that the hoses are not

split or cracked, and listen for leaks in the system.

• Even if significant amounts of water enters the air hose, the AP-2 System should perform

reliably for years. Check the air filters and filter bowl drains on the filters/regulator for

saturation and operation every few weeks.

• Periodically drain the air filters on the air hose to the pumps of collected particles, water

and oil. Draining prevents the filter from clogging up or being otherwise damaged. Check

the regulator to ensure the pressure setting has not drifted appreciably.

• An automatic drain on the compressor is highly recommended, since such an addition

can dramatically increase air filter life and decrease maintenance. Automatic drains are

available from QED.

• The pump can be opened up in the field if the area is clean and dry.

Содержание AutoPump AP-2
















































































































Результаты поиска

Содержание AutoPump AP-2

Отзывы:

Похожие инструкции для AutoPump AP-2

Бренды по названию

Популярные бренды

QED AutoPump AP-2, Руководство по эксплуатации

Результаты поиска

Содержание AutoPump AP-2

Отзывы:

Похожие инструкции для AutoPump AP-2

Бренды по названию

Популярные бренды