QED AutoPump AP-2 Скачать руководство пользователя страница 49

Страница: 49 / 111

Page 41

AP-2 Manual

Revision 7 - August, 2007

Maintenance Table

A visual check and/or maintenance is recommended at least once every two weeks, but

some site environments may demand more frequent service. The following table outlines the

recommended minimum schedule for the AP-2 System.

* Site conditions may require maintenance more often.

The following sections describe each maintenance activity in detail.

Air Quality Check

Single Stage Filter/Regulator Maintenance

Even using air which has some oil and water in it, the AutoPump System should operate

trouble-free for years. The air filter is normally a 5 micron filter with a replaceable

element.

To replace the element in the

air filter

on the single stage filter/regulator

use the following

procedure:

STEP 1 - Disconnect Air Source

•

Valve off the air supply and drain the downstream air to the air filter.

Or disconnect the blue system air supply hose from the single stage

filter/regulator. The

air filters will depressurize, allowing them to be

safely serviced.

WARNING:

Do not remove a filter bowl that is pressurized.

Equipment

Air Quality Check

• Single Stage Filter/Regulator

AutoPump Service

Check Pump Cycle Counter
Check Volume Pumped Per Cycle

Biweekly

Monthly*

As Required

Chapter 6: Maintenance

Содержание AutoPump AP-2
















































































































Результаты поиска

Содержание AutoPump AP-2

Отзывы:

Похожие инструкции для AutoPump AP-2

Бренды по названию

Популярные бренды

QED AutoPump AP-2, Руководство по эксплуатации

Результаты поиска

Содержание AutoPump AP-2

Отзывы:

Похожие инструкции для AutoPump AP-2

Бренды по названию

Популярные бренды