ProMinent Aegis-II, Руководство по сборке и эксплуатации, Страница: 3 / 102

Page 3 of 102
Table of Contents
9.5.3 Calibrating and checking probes ............................................................................................................ 51
9.5.4 Cleaning and servicing probes ................................................................................................................ 51
9.5.5 Calibration Notes ...................................................................................................................................... 52
9.6 G
ENERAL
S
ENSOR
C
ALIBRATION
..................................................................................................................... 53
9.7 C
ALIBRATING AN
A
MPEROMETRIC
S
ENSOR
....................................................................................................... 54
9.8 A
NALOG
S
ENSOR
A
LARMS
............................................................................................................................... 55
9.8.1 Analog Alarm Configuration ..................................................................................................................... 55
9.9 A
NALOG
S
ENSOR
D
IAGNOSTICS
....................................................................................................................... 56
9.9.1 pH-ORP Driver card Diagnostics ............................................................................................................. 57
9.9.2 CT (Conductivity, Boiler Cond., Condensate and Temperature) Driver card Diagnostics ....................... 57
9.9.3 The 4-20mA Input Driver Card Diagnostics ............................................................................................. 57
9.9.4 The 4-20mA output Driver Card Diagnostics ........................................................................................... 57
9.9.5 Serial Sensors (CTFs, LPR, DP) Driver Card Diagnostics ...................................................................... 57
9.10 C
ONFIGURING
D
IGITAL
I
NPUTS
.................................................................................................................... 59
9.10.1 Configure a Digital Input as a Water Meter: ............................................................................................. 59
9.10.2 Link a Water Meter to a Relay (Applies to all relays ) .............................................................................. 60
9.11 D
ISABLE AN
A
NALOG OR
D
IGITAL
I
NPUT
....................................................................................................... 61
9.11.1 Changing or Unlinking an Analog Input Tied to an Output Relay ............................................................ 62
9.11.2 Changing or Unlinking Analog Inputs Tied to a 4-20mA Output: ............................................................. 63
9.11.3 Changing or Unlinking a Digital Input Tied to a Digital Output ................................................................. 63
9.11.4 Changing or Unlinking a Digital Input Tied to a 4-20mA Output .............................................................. 64
9.12 P
HANTOM
I
NPUTS
....................................................................................................................................... 64
10 PROGRAMMING THE CONTROL OUTPUTS (RELAY AND 4-20MA) ......................................................... 64
10.1 F
REQUENCY
/P
ULSE
O
UTPUTS
: .................................................................................................................... 65
10.2 D
ETERMINE IF A
R
ELAY IS
E
NABLED
: ............................................................................................................ 65
10.3 E
NABLE AND
C
ONFIGURE A
R
ELAY
.............................................................................................................. 65
10.4 N
AMING THE
O
UTPUT
................................................................................................................................. 66
10.5 C
ONFIGURING A
B
LOWDOWN
R
ELAY
............................................................................................................ 67
10.6 C
ONFIGURING A
F
EED
R
ELAY
...................................................................................................................... 67
10.6.1 Feed Based on a Water Meter ................................................................................................................. 68
10.6.2 Feed Based on a Sensor ......................................................................................................................... 68
10.6.3 Feed Based on Bleed and/or Feed .......................................................................................................... 69
10.6.4 Feed Based on Percent Time & Base Feed ............................................................................................ 70
10.6.5 Feed Based on a Sensor with Event Control ........................................................................................... 70
10.6.6 Set up a relay using the Feed mode with an oxidant sensor; ORP or any 4-20mA input........................ 70
10.6.7 Choosing a Cycle ..................................................................................................................................... 70
10.7 C
ONFIGURING AN
E
VENT
-O
THER
R
ELAY
...................................................................................................... 71
10.7.1 Schedules, Prebleeding, Lockout and With a Sensor .............................................................................. 71
10.7.2 Add, Remove, Edit Events ....................................................................................................................... 72
10.8 I
NTERLOCKS
............................................................................................................................................... 74
10.8.1 Setting/Removing Interlocks .................................................................................................................... 74
10.9 B
LOCKS
..................................................................................................................................................... 75
10.10 C
ONTROL
A
CTION
(ON D
ECREASES
/ON I
NCREASES
S
ENSOR
): ................................................................ 75
10.11 S
PECIAL
C
ONTROL
F
UNCTIONS
: .............................................................................................................. 76
10.11.1 Timed Cycling: .................................................................................................................................. 77
10.11.2 Time Modulate .................................................................................................................................. 77
10.11.3 PID Control ....................................................................................................................................... 78
10.12 B
OILER
B
LOWDOWN
: .............................................................................................................................. 79
10.12.1 Continuous Boiler Blowdown ........................................................................................................... 79
10.12.2 Captured Sample Blowdown ............................................................................................................ 79
10.12.3 Varying Cycles: ................................................................................................................................ 82
10.13 H
OW TO
S
ETUP A
R
ELAY AS AN
A
LARM
O
UTPUT
: ..................................................................................... 83
10.14 P
RIME
(F
ORCE
O
N
)
A
R
ELAY
................................................................................................................... 83
10.15 S
ENSOR
W
ASH
: ...................................................................................................................................... 83
10.16 4-20
M
A
OUTPUTS
: .................................................................................................................................. 84
10.16.1 How to assign 4-20mA output to control decrease (e.g Acid Feed): ............................................... 84
10.16.2 How to assign 4-20mA output to control increase (e.g Caustic Feed): ............................................ 85
10.16.3 How to assign 4-20mA output to measured value (application: feedback to PLC/DCS): ................ 85
10.16.4 How to set 4-20mA output to Manual Mode: .................................................................................... 86
10.16.5 Linking a 4-20mA Input with a 4-20mA Output ................................................................................ 86
10.16.6 Calibration of a 4-20mA Output ........................................................................................................ 87