PREVOST LE MIRAGE XLII BUS SHELLS, Руководство по обслуживанию

Страница: 134 / 1260

Section 06: ELECTRICAL
PA1564
22
system. With the SYSTEM DIAGNOSTIC menu,
highlight FAULT DIAGNOSTIC and then
highlight ELECTRICAL SYSTEM to request a
diagnostic of the electrical system from the
CECM. Press the enter key. If applicable, the
MCD shows the multiplex device ID, the fault
messages or fault codes recorded. When more
than one fault is recorded, an arrow pointing
down appears on the right of the display. Use the
down arrow to see all the fault messages.
Once the problem corrected, the MCD still shows
the fault as being active. You have to leave the
FAULT DIAGNOSTIC menu, wait approximately
20 to 30 seconds and then return to FAULT
DIAGNOSTIC to request a new diagnostic of the
ELECTRICAL SYSTEM from the CECM. The
MCD should display the fault as being inactive.
The CECM can store up to 20 faults, i.e. the first
10 and the last 10. Middle faults will be erased. If
the breakers are tripped, the fault history will be
erased from the CECM memory.
NOTE
When performing an electrical system diagnostic
with the MCD (message center display), the
message “No Response ModA41” indicates
either module A41 is not responding due to a
CAN link problem or module A41 is not
powered. Similar messages exist for all modules
(A42, A43, A44, etc.).
Because it is easier to do, check first if the
module is powered by probing on its gray
connector. If it is, then you can conclude that
there is a CAN link problem. Refer to paragraph
4.6: CAN NETWORK LAYOUT AND TROUBLE-
SHOOTING in this section.
NOTE
It is of the utmost importance to have a MCD
(message center display) in working condition
because it is the most important tool to achieve
troubleshooting on a multiplex vehicle.
4.2 PROBING VOLTAGE ON THE
MULTIPLEX CIRCUITS
Some Multiplex modules are supplied by 12 volts
while others are supplied by 24 volts. The 12-volt
or 24-volt information is found on the modules
symbol in the wiring diagram. Before taking
voltage readings to track the source of a
problem, first verify if the module is supplied by
12V or 24V, if not, residual voltage on the
module inputs/outputs can draw an erroneous
conclusion.
Inactive Multiplex output = Residual voltage of
18% to 33% of supply voltage.
Inactive Multiplex input = Residual voltage of
50% of supply voltage.
NOTE
o
Verify on the wiring diagram whether the
voltage is 12V or 24V,
o
For a 12V module: an active voltage would
be 12V or 0V but not in between. If you
measure the intermediate tensions (ex. 6V,
2V, or 4V) this must be interpreted as if the
input or the output is inactive.
o For a 24V module: an active voltage would
be 24V or 0V but not in between. If you
measure the intermediate tensions (ex. 12V,
4V, or 8V) this must be interpreted as if the
input or the output is inactive.
4.3 CAN NETWORK
The CAN link wiring is separated in sections and
uses connectors that are not shared with other
circuits. This allows sections of the network to be
isolated to help locate short-circuit on the CAN.
In case of a short-circuit on the CAN link, this
affects all the modules and they all show
« No
Response » in the error messages of the
« ELECTRICAL SYSTEM » menu. To locate a
short-circuit, proceed by disconnecting one
module zone at a time while verifying if this
makes inactive the errors in the modules still
connected. Connector C1 (front electrical &
service compartment) disconnects all the
modules at the rear of the vehicle from the
network. Connector C5 (front electrical & service
compartment) disconnects all the modules from
the wiper control panel. Connector C100
disconnects the module from the evaporator
compartment. Connector C3 (rear junction box)
disconnects the modules from the battery
compartment.
Example: Disconnect C5 and C1 and then verify the
status of the errors. If the front modules (A41 to A46)
now give inactive errors, which means short-circuit is
elsewhere than in the front electrical & service
compartment.
4.3.1 Can Connection On The Telltale Panel
And The Hvac Control Unit