Pottinger SK 2740 Скачать руководство пользователя страница 37

Страница: 37 / 76

- 37 -

2000-DE HANGFAHRT_2740

Working on slopes

WARNINg

Risk of serious injury or injury resulting in death

due to the tractor/trailer combination tipping on

slopes, particularly in transport position and driving

on bends.

•

Reduce general speed accordingly, espe-

cially when cornering.

•

Drive backwards on the slope rather than

carry out a risky turning manoeuvre.

The tractor's driving characteristics are influenced by the

weight (G) of the rotor unit This can lead to dangerous

situations, especially on inclines.

TD 33/97/

Folding on slopes

WARNINg

Risk of serious injury or injury resulting in death

when folding out on the slope

•

If possible, avoid carrying out folding proce-

dures on the slope!

•

Only carry out folding procedures on the

slope if the device is aligned at a 90° angle

to the slope.

•

Lowering procedures on the slope should

always be carried out in one go! If lower-

ing is interrupted, undefined movements

may occur in the rotor which can cause the

device to tip.

The driving characteristics of the tractor are influenced by

the weight (G) of the rotor unit. This can lead to dangerous

situations, especially on slopes.
If the alignment of the device at a 90° angle to the slope

does not function either:

•

Begin with the rotor unit facing up the slope

when folding out.

•

Begin with the rotor unit facing down the

slope when folding up.

TD 33/97/

Содержание SK 2740













































































Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды

Pottinger SK 2740, Руководство оператора

Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды