Pottinger SK 2740 Скачать руководство пользователя страница 13

Страница: 13 / 76

- 13 -

1900-EN_Schleppervoraussetzungen_2740

TracTor requiremenTs

Tractor

To operate the implements the following tractor requirements

must be met:

-  Tractor power:
  TOP 842 C / TOP 882 C from 55 kW / 75 HP
  TOP 962 C from 62kW / 85HP
-  Attaching:

Lower link Cat. II

- Connections: See table "Necessary hydraulic and

power connections"

Ballast weights

The front of the tractor must have sufficient ballast weights

to guarantee braking and steering capabilities.

DANgER

Risk of death or property damage due to incorrect

tractor balast.

•

The front axle of the tractor must always be

loaded with at least 20% of the tractor's tare

weight to guarantee the steering and braking

capacity of the tractor/trailer unit.

20%

lifting unit (three-point linkage)

371-08-16

371-08-16

- The tractor’s lifting unit (three-point linkage) must be

designed for the occurring load. (See technical data)

- The lifting struts are to be set at the same length (4)

using the appropriate adjusting device

(See the tractor manufacturer’s operating manual)
- Select the rear position if the lifting rods can be set in

various positions on the lower link. This relieves the

pressure on the tractor’s hydraulic system.

- The limiting chain or lower link stabilisers (5) are to

be set so that the attached machine CANNOT move

sideways. (Safety measure for transportation)

Содержание SK 2740













































































Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды

Pottinger SK 2740, Руководство оператора

Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды