Pottinger SK 2740 Скачать руководство пользователя страница 64

Страница: 64 / 76

- 64 -

1800_DE-ANHANGA_SICHERHEIT

annex -a

safeTy advice

10.) Asbestos

a. Certain sub-supplied components of the vehicle may

contain asbestos due to technical reasons. Please

observe the marking of spare parts.

11.) Transport of people prohibited

a. The transport of people on the machine is not permitted.
b. The machine may only be driven on public roads when

in the position stipulated for road transport.

12.) Driving ability with auxiliary equipment

a. The towing vehicle is to be sufficiently equipped with

weights at the front or at the rear in order to guarantee

the steering and braking capacity (a minimum of 20%

of the vehicle’s tare weight on the front axle).

20%

b. The driving ability is influenced by the road and

auxiliary equipment. The driving must be adapted to

the corresponding terrain and ground conditions.

c. When driving through curves with a connected

implement, observe the radius and swinging mass of

the implement!

d. When travelling in a curve with attached or semi-mounted

implements, take into account the working range and

swing mass of the implement!

13.) general

a. Before attaching implements to the three-point linkage,

move system lever into a position whereby unintentional

raising or lowering is ruled out!

b. Danger of injury exists when coupling implements to

the tractor!

c. Danger of injury through crushing and cutting exists in

the three-point linkage area!

d. Do not stand between the tractor and the implement

when using three-point linkage external operation!

e. Attach and detach drive shaft only when motor has

stopped.

f. When transporting with raised implement, secure

operating lever against lowering.

g. Before leaving tractor, lower attached implement to the

ground and remove ignition key!

h. Nobody is allowed to stand between tractor and

implement without the tractor being secured against

rolling using parking brake and/or wheel chocks!

i. For all maintenance, service and modification work,

turn driving motor off and remove the universal drive.

14.) Cleaning the implement

a. Do not use high-pressure washers for the cleaning of

bearing and hydraulic parts.

Содержание SK 2740













































































Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды

Pottinger SK 2740, Руководство оператора

Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды