Pottinger SK 2740 Скачать руководство пользователя страница 67

Страница: 67 / 76

- 67 -

1700_ GB-Cardan shaft_BA-ALLG

Cardan shaft

Supplement - B

Ensure sufficient swivel space for the cardan shaft!
- Trim the safety chain so that it cannot wind around the

cardan shaft.

Instructions for working

Do not exceed the permissible pto speed when using the

machine.
- The attached machine may run-on after the pto is

switched off. Work must only be performed on it once

it has completely stopped.

- When parking the machine, the cardan shaft must be

taken off or secured using a chain, as instructed. Do

not use safety chain (H) to suspend the cardan shaft.

Wide-angle joint:

  Maximum angle for operation and at standstill 70°.
Standard joint :
  Maximum angle at standstill 90°.
  Maximum angle for operation 35°.

DANgER

mortal danger - due to worn covers

•

Replace the worn covers immediately

Adapting cardan shaft to tractor

NOTE

material damage - due to inferior spare parts

•

Only use the cardan shaft supplied or stat-

ed; otherwise the warranty claims for any

damage are not valid.

The correct length is determined by comparing both cardan

shaft halves.

Cutting to length procedure

- To adapt the length, hold cardan shaft halves side by

side in the shortest operating position (L2) and mark.

Caution!

• Note the maximum operating length (L1)

- Try for the greatest possible tube overlap (min. 1/2

•  Trim the inner and outer protective tube equally
•  Attach overload protection (2) to the machine!
•   Always check that drive shaft locks are securely engaged

before starting work.

Safety chain

- Use chain to prevent tube guard from rotating.

Содержание SK 2740













































































Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды

Pottinger SK 2740, Руководство оператора

Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды