Pottinger SK 2740 Скачать руководство пользователя страница 41

Страница: 41 / 76

- 41 -

1902-GB Maintenance_2740

mainTenance

Set tyre tracking

Tyre tracking for the right and left tyres can be adjusted

from the rear steering linkage.

1.  Open the locknuts (7, 8) (left and right threads)
2.  Turn the tie rod (9) until the track is set correctly.
3.  Lock the bar with the nuts (7, 8).

- Set the toe-in to maximum 5 mm. This means the

distance of the tyre's front edge must be 5 mm less

than the distance of the tyre's rear edge. (in direction

of travel)

- The distance of the tie bar heads for the left and right

tie bars must be the same.

Tyres

Dimensions

Air pressure

Chassis

1. *380 / 54 - 17 138A8

Flot+ ET -54

2. *340 / 55 - 16 133A8

Flot+ ET -50/6L

3. *15.0 / 55 - 17 12PR

AS ET -54/6L

1.5 bar

Rotor

16 / 6.50 - 8 10PR

1.5 bar

NOTE

Risk of material damage due to excessive forces

acting on the steering.

•

Tyres marked with a * may only be fitted in

the position which is narrower due to the

offset, otherwise excessive forces will act

on the steering. This only applies to devices

with steered chassis. If the frame is rigid, the

tyres can be mounted in both positions.

289-12-34

ET -50 / -54

Tine arms

Change tine arms

- Loosen cover bolts (10).

- 1. Remove 2x bolts M12x110 (11)
2. Loosen 4x bolts M12x110 (12).

- Pull cover off
- Pull tine arm out. Turn the rotor unit so that the old

tine arm can be pulled out between the intake and

output (see below).

- Insert new tine arm. Turn the rotor unit so that the

new tine arm can be inserted between the intake

and output control (see below).

Direction of

travel

Содержание SK 2740













































































Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды

Pottinger SK 2740, Руководство оператора

Результаты поиска

Содержание SK 2740

Отзывы:

Похожие инструкции для SK 2740

Бренды по названию

Популярные бренды