Potterton Eurocondense three Скачать руководство пользователя

Страница: 56 / 120

Temperature difference (4130 - 4133)

Temp diff on/off

(4130, 4131)

Comparative temp

(4133)

A sufficiently large temperature difference is necessary between the boiler tem-

perature and the comparative temperature for start-up of the pump.

Fig. 15: Storage tank charging

TBx

Temp diff on

Temp diff off

Off

TSt

TBx

ON/OFF

Boiler temp

Comparative actual temperature

ON/OFF Boiler pump

To maintain the comparative temperature, the following settings are available

under prog. no. 4133:

DHW sensor B3/B31:

The comparative temperature is supplied by the DHW sen-

sor B3/B31

Storage tank sensor B4/B41:

The comparative temperature is supplied by the buf-

fer storage tank sensor B3/B31

Flow temp setpoint:

The flow temperature setpoint is used as comparative tem-

perature.

Setpoint min

The value set in prog.no. 4110 is used as comparative temperature.

Pump after-run time (4140)

Pump after-run time

(4140)

Setting pump after-run time.

Buffer storage

Auto generation lock

(4720)

The hydraulic separation of heat source and buffer storage tanks achieved by the

automatic heat generation lock. The heating source will only be started if the buf-

fer storage tank cannot cover the actual heat request. The following settings are

possible:

None

: the automatic heat generation lock is de-activated.

with B4

: the automatic heat generation lock will be triggered by the buffer sto-

rage tank B4

with B4 and B42/B41

: the automatic heat generation lock will be triggered by

the buffer storage tanks B4 and B41/B42.

Auto heat gen lock SD

(4721)

The heat source will be locked if the temperature in the buffer storage tank is hig-

her than the boiler s auto heat generation lock SD.

Programming

Gas-fired fuel value boiler EuroCondense three 125-300 kW

358 488 09.10

Содержание Eurocondense three

























































































































Результаты поиска

Содержание Eurocondense three

Отзывы:

Похожие инструкции для Eurocondense three

Бренды по названию

Популярные бренды

Potterton Eurocondense three, Руководство по программированию

Результаты поиска

Содержание Eurocondense three

Отзывы:

Похожие инструкции для Eurocondense three

Бренды по названию

Популярные бренды