Potterton Eurocondense three Скачать руководство пользователя

Страница: 59 / 120

Flow setpoint boost

(5020)

The boiler temperature setpoint for charging the DHW storage tank consists of

the DHW temperature setpoint and the flow setpoint boost.

Transfer boost

(5021)

Through the transfer, energy can be moved from the buffer storage tank into the

DHW storage tank. For this the current buffer storage tank temperature must be

higher than the current temperature in the DHW storage tank. This temperature

difference is set here.

Type of charging

(5022)

Charging a layer storage:

- Charging: The first charging of each day will heat-up the hot water tank com-

pletely.

- Re-charging : all the following re-charges afterwards will heat-up the water

above the hot water sensor.

Re-charging

: In general, the demand of domestic hot water is controlled by the

upper tank sensor TWF (B3).

Charging

: The demand of domestic hot water is controlled by the two tank sen-

sors (B3) and TLF (B36).

Charging Legio

: Legionella function being active: both sensors control the de-

mand of domestic hot water, otherwise the upper sensor TWF (B3) only.

Charging 1. Charge

: During the 1st charge of the day: both sensors control the

demand of domestic hot water, otherwise the upper sensor TWF (B3) only.

Full charg 1st time legio. Charge

: During the 1st charge of the day: both sensors

TWF (B3) and TLF (B36) control the demand of domestic hot water, otherwise

the upper sensor TWF (B3) only.

Switching diff

(5024)

If the DHW temperature is lower than the current setpoint minus the switching

difference set here, the DHW charging is started. The DHW charging is ended if

the temperature of the current setpoint is reached.
At the first DHW release of the day, a forced charging is performed.

The DHW charging is also started if the DHW temperature is within the switching

difference - as long as it is not less than 1 K under the setpoint.

Charging time limitation

(5030)

During the DHW charging, the room heater - depending on the selected charging

priority (prog.no. 1630) and the hydraulic switch – has too little or no power. Of-

ten it is therefore practical to restrict the time of DHW charging.

Discharging prot

(5040)

The function ensures that the DHW pump (Q3) first switches on if the temperate

in the heat generator is sufficiently high.

Application with sensor

The charging pump is first switched on if the heat source temperature is above

the DHW temperature plus the half of the charging increase. If the boiler tempe-

rature drops again below the DHW temperature plus 1/8 of the charging excess

during the charging, the charging pump is again switched off. If two DHW sen-

sors for the DHW charging are parameterized, the lower temperature is consider-

ed for the discharge safety function (normally the DHW sensor B31).

Application with thermostat

The charging pump is first switched on if the boiler temperature is above the

DHW nominal setpoint. If the boiler temperature drops below the DHW nominal

setpoint minus the DHW switching difference, charging pump is again switched

off.

Off:

the function is switched off.

Always:

the function always affects.

Automatic

The function only takes effect if the heat generator cannot deliver heat

or is not available (malfunction, heat source block).

Programming

358 488 09.10

Gas-fired fuel value boiler EuroCondense three 125-300 kW

Содержание Eurocondense three

























































































































Результаты поиска

Содержание Eurocondense three

Отзывы:

Похожие инструкции для Eurocondense three

Бренды по названию

Популярные бренды

Potterton Eurocondense three, Руководство по программированию

Результаты поиска

Содержание Eurocondense three

Отзывы:

Похожие инструкции для Eurocondense three

Бренды по названию

Популярные бренды