manualshive.com logo in svg

Potterton Eurocondense three, Руководство по программированию, Страница: 71 / 120

Поделиться
Скачать
Potterton Eurocondense three Скачать руководство пользователя страница 71

Tab. 5: Check no. heating circuit (prog.-no. 6217)

Heating circuit 3

Heating circuit 2

Heating circuit 1

0 No heating circuit

00 No heating circuit

00 No heating circuit

1 Circulation via boiler pump

01 Circulation via boiler pump

01 Circulation via boiler pump

2 Heating circuit pump

02 Heating circuit pump

02 Heating circuit pump

3 Heating circuit pump, mixing

valve

03 Heating circuit pump, mixing

valve

03 Heating circuit pump, mixing

valve

Software version

(6220)

  Display of the actual software version.

LPB-system

Device address/Segment add-

ress

(6600/6601)

  The two-part LPB address of the controller consists of the 2-digit segment num-

ber and the 2-digit device number.

Bus power supply function

(6604)

  -

Off

: the power supply of the bus system does not take place through the con-

troller.

-

Automatically

: the power supply of the bus system is switched on and off by

the controller depending on the power requirement of the bus system..

Bus power supply state

(6605)

  -

Off

: the power supply of the bus system through the controller is currently inac-

tive.

-

On

: the power supply of the bus system through the controller is currently acti-

ve.

Display systemmessages

(6610)

  This setting allows system messages which are transmitted via LPB to be suppres-

sed on connected operating elements.

Alarm delay

(6612)

  Settling out of the alarm on the BM module can be delayed in the base device by

an adjustable time. This allows the prevention of unnecessary messages to a ser-

vice location from briefly occurring malfunctions (e.g. temperature monitor quer-

ied, communication errors). However, it must be realised that briefly occurring

malfunctions which continue and quickly occur again, are also filtered out with

this.

Display systemmessages

(6610)

  If the setting Central is activated under progr. no. 6221 and 6223, the action for

this setting can be set. The following settings are possible:

-

Segment

: the changeover is done for all controllers in the same segment.

-

System

: the changeover is done for all controllers in the entire system (that is in

all segments). The controller must be located in segment 0!

Summer changeover

(6621)

  -

Locally

: the local heating circuit is switched on and off depending on prog. no.

730, 1030 or 1330.

-

Centrally

: depending on the settings made in prog no. 6620 either the heating

circuit in the segment or in the entire system is switched on and off.

Optg mode changeover

(6623)

  -

Locally

: the local heating circuit is switched on and off.

-

Centrally

: depending on the settings made in prog no. 6620 either the heating

circuit in the segment or in the entire system is switched on and off.

Programming

358 488 09.10

Gas-fired fuel value boiler EuroCondense three 125-300 kW

71

Содержание Eurocondense three

























































































































Отзывы:

Нет отзывов