manualshive.com logo in svg

Potterton Eurocondense three, Руководство по программированию, Страница: 68 / 120

Поделиться
Скачать
Potterton Eurocondense three Скачать руководство пользователя страница 68

Fig. 18: Example for Heat request 10 V and Refrigeration request 10 V

Flow setpoint

[°C]

F2=130

F2=100

F1=0

Voltage at Hx
[V]

U1=0

0,15

U1=10

F1

  Function value 1

F2

  Function value 2

U1

  Voltage value 1

U2

  Voltage value 2

 

PWM-output P1

(6085)

  With this parameter the function for the modulating pumps is specified. If becau-

se of the function no modulating signal can be calculated internally, then 0 % for

Off

 or 100 % for 

On

 is output.

-

None

: No output P1 exists.

-

Boiler pump Q1

: the connected pump is used for recirculation of the boiler wa-

ter.

-

DHW pump Q3

: Control element for drinking water storage.

-

DHW interm circ pump Q33

: Charge pump for domestic hot water storage with

external heat exchanger.

-

Heat circuit pump HC1 Q2

: the heat circuit pump HC1 will be activated.

-

Heating circuit pump HC2 Q6

: the heat circuit pump HC2 will be activated.

-

Heating circuit pump HC3 Q20

:the heat circuit pump HC3 will be activated.

-

Collector pump Q5

: a circulation pump for the collector circuit is required for

connection of a solar collector.

-

Solar pump ext exch K9

: if several exchangers are connected, the buffer storage

must be set at the respective relay output. and the type of the solar regulating

unit must be defined in prog.no. 5840.

-

Solar pump swi pool K18

: if several exchangers are connected, the the swim-

ming pool must be set at the respective relay output. and the type of the solar

regulating unit must be defined in prog.no. 5840.

.

Sensor type collector

(6097)

  Selection of used sensor types for measurement of the collector temperature.

Readjustm coll sensor 1

(6098)

  Setting a correction value for collector sensor 1.

Readjustm outside sensor

(6100)

  Setting a correction value for outside sensor.

Programming

68

Gas-fired fuel value boiler EuroCondense three 125-300 kW

358 488 09.10

Содержание Eurocondense three

























































































































Отзывы:

Нет отзывов