Potterton Eurocondense three Скачать руководство пользователя

Страница: 55 / 120

Evaporation heat carrier

(3860)

Pump protecting function, to prevent overheating of the collector pump in case of

evaporating danger of the heat carrying medium due to high collector tempera-

ture.

Antifreeze

(3880)

Information of the antifreeze used.

Antifreeze concentration

(3881)

Input of antifreeze concentration for usage measurement of solar energy.

Pump capacity

(3884)

Input of the flow of the installed pump for calculation of the brought in volume

for usage measurement.

Pulse valency

(3887)

Defines the flow per pulse for the H4 inlet. The H4 inlet must be configured to

pulse count for this.

Solid fuel boiler
Locks other heat sources (4102)

Locks other heat sources

(4102)

If the solid fuel boilers are activated, other heat generators, e.g. oil./gas boilers,

are blocked, as soon as an increase in the boiler temperature is discovered that

points to the exceeding of the comparative temperature (prog. no. 4133).

Setpoint min (4110)

Setpoint min

(4110)

The boiler pump is only put into operation if the boiler temperature has reached

the minimum setpoint set here in addition to the necessary temperature diffe-

rence.

Programming

358 488 09.10

Gas-fired fuel value boiler EuroCondense three 125-300 kW

Содержание Eurocondense three

























































































































Результаты поиска

Содержание Eurocondense three

Отзывы:

Похожие инструкции для Eurocondense three

Бренды по названию

Популярные бренды

Potterton Eurocondense three, Руководство по программированию

Результаты поиска

Содержание Eurocondense three

Отзывы:

Похожие инструкции для Eurocondense three

Бренды по названию

Популярные бренды