Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя

Страница: 83 / 147

3. Unlatch the air box cover clips

and carefully remove the air box cover.

4. Remove the air filter

from the air box.

5. Inspect the air filter. Shake the filter to remove excess dirt. If the filter remains

caked with dirt, replace the filter with a new filter.

6. Clean the inside of the air box using a vacuum.

NOTICE

Avoid using compressed air for cleaning as dirt could enter the engine.

7. Reinstall the air filter or install a new air filter.

CAUTION

Operating the vehicle without the air filter installed can result in serious engine

damage, which could result in an accident and injury to the operator and

others. Always make sure the air filter is installed.

8. Reinstall the air box cover and secure the clips.

9. Close the hood.

AIR FILTER (IF EQUIPPED)

Always inspect the air filter at the intervals outlined in the Periodic Maintenance
Chart. Replace the air filter every 15,000 miles (24,000 km).

1. Open the hood.

2. Loosen the clamp

from the air filter.

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды