Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя

Страница: 114 / 147

3. Apply a light coat of oil or grease to all bushings, spindle shafts and tie rod

ends.

4. Change the engine oil. Start the engine and allow it to idle just long enough

to circulate the new oil throughout the engine.

5. Fog the engine using the recommended aerosol fogging oil available from

your dealer. Follow the instructions on the container.

6. Treat the fuel system with a fuel stabilizer. If a fuel stabilizer is not used, the

fuel tank, fuel lines and fuel rail should be completely drained of gasoline.

7. Remove the spark plugs. Spray a light amount of engine fogging oil into each

cylinder to prevent rust. Reinstall the plugs.

8. Make sure the coolant quality and level in the system is adequate for freeze

protection during storage.

9. Apply a metal protectant to shock absorber shafts or any exposed metal to

prevent corrosion.

10. Separate electrical connector blocks and clean corrosive build-up from

connectors. Replace worn or frayed electrical wire and connectors.

11. Prepare the battery for storage.

12. Verify that tire pressure is at specification.

13. Cover intake and exhaust openings to prevent small animals from entering.

14. Elevate the vehicle using appropriate jack stands. Remove the wheels to

prevent flat spots on the tires.

15. Do not engage the park brake. If engaged, the brake pads may stick to the

discs.

16. Cover the vehicle with a fabric cover. Do not use plastic or vinyl covers,

which trap moisture and encourage rust and corrosion.

BATTERY STORAGE

1. Remove the battery.

2. Clean the battery terminals first with a wire brush to remove any loose

deposits.

3. Wash the posts and the ends of the battery cables with a solution of one part

baking soda to 16 parts water. Rinse with clean water and wipe dry.

4. Apply a thin film of dielectric grease to the posts and cable connectors.

5. Clean the outside of the battery with a solution of mild detergent and warm

water.

112

CLEANING AND STORAGE

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды