Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 44

Страница: 44 / 147

SEAT BELTS

This vehicle is equipped with three-point lap and diagonal seat belts on all seats.
Always make sure the seat belts are secured for the driver and passenger
before operating.

WARNING

The SLINGSHOT is a motorcycle (not a car) and does not meet automotive

frontal crash and impact standards. In the event of a rollover or crash, an

unbelted person is significantly more likely to be thrown from a vehicle and die

than a person wearing a safety belt.

To wear the seat belt properly, follow this procedure:

1. For 3-point belts, pull the seat belt latch downward and across your chest

toward the latch housing

at the outer edge of the seat. The belt should fit

snugly across your hips and diagonally across your chest. Make sure the belt
is not twisted.

2. Push the latch plate

into the latch housing until it clicks.

FEATURES AND CONTROLS

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды