Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя | Manualshive

Страница: 50 / 147

background image

Turn the ignition key to the ON position before performing the electrical pre-ride
inspections. Return the ignition key to the OFF position after completing these
inspections. If inspection of any electrical item reveals component failure, repair
or replace the component before operating the vehicle.

ITEM

INSPECTION PROCEDURE

SEE

PAGE

Electrical

Front Lights

Turn the ignition key on. Verify that the headlights, auxiliary
lights (if equipped) and park lamps illuminate. Switch to high
beam. Verify that the high beam indicator comes on and that
headlamp brightness increases. Adjust headlight aim as
needed.

Rear Lights

Verify that the taillights and license plate light illuminate. Apply
the brakes and verify that the taillight lamps increase in
brightness.

-

Turn Signals

Verify that the left and right turn signals flash at the front and
rear of the vehicle, and that the corresponding indicator lamp
flashes in the gauge.

-

Emergency
Flashers

Press the top of the hazard switch to turn the flashers on.
Verify that all four turn signals flash, as well as the lamps in the
gauge. Press the bottom of the switch to turn the flashers off.
Verify that all signals and indicator lamps stop flashing.

-

Horn

Press the horn button. Verify that the horn sounds loudly.

-

Low Oil
Pressure
Indicator

Start the engine and verify that the low oil pressure lamp does
not illuminate.

-

Steering

Check power steering for smooth operation.

General

Engine Oil
Level

Check the oil level.

Fuel Level

View the fuel gauge to check the fuel level.

Coolant Level

Check the recovery bottle coolant level.

Tires

Inspect tire condition, pressure and tread depth.

Wheels

Inspect for loose, damaged or missing wheel nuts.

Brake Fluid
Level

Check the master cylinder brake fluid level.

Park Brake

Verify that the vehicle does not roll when the park brake is set.

Brake System

Inspect brake system hoses, connections and brake pads.
Check brake pedal for excessive travel or a spongy feel.

48

PRE-RIDE INSPECTIONS

Downloaded from

«
...
48
49
50
51
52
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: JETBAG Страницы: 44

Бренд: Brodit Страницы: 2

Бренд: Motoalliance Страницы: 8

Бренд: Jeep Страницы: 380

Бренд: SAN HIMA Страницы: 7

Peterbilt SmartAir

Бренд: Paccar Страницы: 58

Бренд: Mercedes-Benz Страницы: 153

Dodge Challenger SRT8®Challenger SRT8 392 2012

Бренд: Dodge Страницы: 5

Бренд: Edelbrock Страницы: 2

Бренд: TATA Motors Страницы: 92

Бренд: Westfalia Страницы: 10

Sedan CIVIC 2022

Бренд: Honda Страницы: 701

Бренд: r.LiNK Страницы: 20

Crossland X 2017

Бренд: Vauxhall Страницы: 245

Бренд: Yakima Страницы: 10

Бренд: Yakima Страницы: 10

Бренд: Lexus Страницы: 609

Бренд: Kargo Master Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды