Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя

Страница: 32 / 147

5. Press and hold the MODE button to exit the diagnostics code menu.

6. See your authorized dealer for code details and diagnosis.

Error Code Number (0-9)

Suspect Parameter Number (SPN)

Failure Mode Indicator (FMI)

DISPLAY SCREEN

WARNING

Driving while distracted can result in loss of vehicle control, crash, and injury.

We strongly recommend that you use extreme caution when using any device

that may take your focus off the road. Your primary responsible is the safe

operating of your vehicle. We recommend against the use of any hand-held

device while driving and encourage the use of voice-operated systems when

possible. Make sure you are aware of all applicable local laws that may affect

the use of electronic devices while driving.

FEATURES AND CONTROLS

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды