Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 39

Страница: 39 / 147

1. Pull the adjustment lever downward to unlock the steering column

2. Move the steering wheel upward or downward to the desired position.

3. Push the adjustment lever upward to lock the steering column in position.

Make sure the lever is fully seated.

WARNING

Make sure the wheel is positioned so that it rotates freely and allows enough

room between your legs and the rim of the wheel for your hands to pass

without obstruction. Failure to do this could cause difficulty steering and result

in loss of control.

FEATURES AND CONTROLS

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды