Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя | Manualshive

Страница: 106 / 147

background image

LED LIGHT ASSEMBLIES

LED lights are not serviceable. If one of the LED lamps fails to illuminate, the
entire light assembly must be replaced.

1. Remove the rear body panel to access the light assembly.

2. Remove the screws

q

securing the light assembly to the vehicle (taillight

assembly shown).

3. Unplug the electrical connector

w

from the light assembly.

4. Remove the light assembly.

5. Install the electrical connector to the replacement light assembly.

6. Reinstall the light assembly. Tighten the screws.

TORQUE

3 ft-lbs (4 Nm)

7. Reinstall the rear body panel. Tighten the screws.

TORQUE

5.4 ft-lbs (7 Nm)

HEADLAMP AIM INSPECTION CONDITIONS

The following headlamp aim inspections and adjustments will be accurate only
when tire pressures and suspensions are at factory-recommended settings.
Refer to safety labels on the vehicle or to the specifications section beginning on
page 121. The vehicle must also be unladen (without fuel, rider weight or cargo
weight).

104

Downloaded from

«
...
104
105
106
107
108
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: Westin Страницы: 3

Бренд: NavLinkz Страницы: 4

Бренд: Conrad Страницы: 26

2003 Thunderbird

Бренд: Ford Страницы: 200

Бренд: Kia Страницы: 54

Бренд: Metra Electronics Страницы: 2

Бренд: Yakima Страницы: 12

Бренд: FALCON RIDGE Страницы: 6

Бренд: AIS Страницы: 2

Бренд: Xpresskit Страницы: 18

Бренд: Thule Страницы: 3

Бренд: Acura Страницы: 7

Multi Vehicle Mount MVM-35-05

Бренд: Bracketron Страницы: 4

Бренд: Blaupunkt Страницы: 6

Outlander Plug-in hybrid

Бренд: Mitsubishi Страницы: 28

DH-RB 05.02 Series

Бренд: Dhollandia Страницы: 65

Бренд: BMW Страницы: 278

2004 JR41 Stratus Sedan

Бренд: Dodge Страницы: 273

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды