Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя | Manualshive

Страница: 67 / 147

background image

MAINTENANCE

INTRODUCTION

Proper maintenance assures the highest level of safety, durability and
dependability for your SLINGSHOT vehicle.

Owners are responsible for performing the scheduled maintenance identified in
this owner’s manual.

• Your authorized SLINGSHOT dealer can perform the break-in maintenance

procedures when the vehicle’s odometer registers 500 miles (800 km).

• See your dealer or perform the recommended periodic maintenance at the

intervals specified in the Periodic Maintenance Chart beginning on page 67.

Any qualified repair shop or person may maintain, replace, or repair the
emission control devices or systems on your vehicle. An authorized POLARIS
dealer can perform any service that may be necessary for your vehicle.
POLARIS also recommends POLARIS parts for emissions related service.
However, equivalent parts may be used for such service. It is a potential
violation of the Clean Air Act if a part supplied by an aftermarket parts
manufacturer reduces the effectiveness of the vehicle's emission controls.
Tampering with emission controls is prohibited by federal law.

BREAK-IN MAINTENANCE

Your dealer can perform the break-in maintenance procedures when the
vehicle’s odometer registers 500 miles (800 km). Performing the break-in
maintenance will help ensure optimum engine performance for the entire service
life of the engine. Your dealer can change engine oil, inspect all fluids and
serviceable components, ensure that all fasteners are tightened and make other
adjustments as needed.

MAJOR MAINTENANCE

For major repair information, refer to the

SLINGSHOT Service Manual

. Major

repairs typically require technical skills and specially designed tools. Emission
system service requires special tools and training and should be performed by
your dealer.

SAFETY DURING SERVICE PROCEDURES

WARNING

Failure to follow recommended precautions and procedures could result in

severe injury or death. Always heed all safety precautions and follow all

operation, inspection and maintenance procedures outlined in this manual.

65

Downloaded from

«
...
65
66
67
68
69
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: KC HiLiTES Страницы: 4

Бренд: GARO Страницы: 23

LS4 Wallmounted

Бренд: GARO Страницы: 15

Бренд: Chevrolet Страницы: 494

Бренд: Acura Страницы: 2

Бренд: Mercedes-Benz Страницы: 54

Бренд: BMW Страницы: 38

Бренд: Whelen Engineering Company Страницы: 9

MagicSafe MSG150

Бренд: Waeco Страницы: 20

Бренд: SSV Works Страницы: 2

Бренд: Lexus Страницы: 878

Sportsman 40-0125

Бренд: Westin Страницы: 2

Бренд: Erich Jaeger Страницы: 16

Бренд: Ranger design Страницы: 6

Бренд: TRAMEC Страницы: 116

Бренд: ZeroRPM Страницы: 41

Бренд: Yakima Страницы: 12

Бренд: Axxess Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды