Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 147

background image

LAMP

INDICATES

CONDITION

Turn Signal
Hazard
Signals

The left turn signal is on the speedometer. The right turn
signal is on the tachometer. Both arrows flash when either
a turn signal or the hazard signal is activated.

If a lamp

fails, or if there is a short circuit in the signal system, the
lamp flashes at more than twice the normal rate.

Low Fuel

This lamp illuminates when approximately one gallon (3.8
liters) of fuel remains in the fuel tank.

Hot Engine

This lamp illuminates to indicate an overheated engine. If
the indicator flashes, the overheating condition remains,
and the system will automatically reduce engine power.

Check Engine

If this lamp illuminates while the engine is running, promptly
contact an authorized dealer or another qualified person
who can assist with diagnosis.

If abnormal engine

operation is detected the light will remain on as long as the
fault condition exists. Retrieve the error codes for
diagnosis. See page 29. This lamp is also known as a
malfunction indicator lamp (MIL).

Low Battery
Voltage

This lamp illuminates when battery voltage is low (or when
voltage is above the normal range). Turn non-essential
accessories off to conserve power. Make sure the charging
system is operating properly.

Traction
Control

This lamp illuminates if the user disables traction control
with the ESP Switch. See page 23.

ESP Disabled

This lamp illuminates if the user disables the ESP with the
ESP Switch. Always enable the ESP for normal operation.
See page 23.

ESP
Intervention

The ESP Intervention lamp

flashes

when the ESP is

actively assisting. The lamp illuminates

solid

to indicate a

system failure. If the lamp illuminates solid, your dealer can
inspect the vehicle and perform service.

Brake Failure

This lamp illuminates if a brake component is not operating
properly. Do not operate the vehicle. Inspect brake fluid
levels. Your dealer can inspect the vehicle and perform
service.

Seat Belt

The seat belt lamp illuminates whenever the key is in the
ON position and the driver’s seat belt is not fastened.

EPAS
Warning

This lamp illuminates briefly when the key is turned to the
ON position. If the ignition is left on for 5 minutes without
starting the engine, the lamp illuminates to indicate that the
EPAS has shut down to conserve battery power. If the lamp
illuminates after starting the engine, the power steering

26

FEATURES AND CONTROLS

Downloaded from

«
...
26
27
28
29
30
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: Vauxhall Страницы: 2

SmartDiag2GO GD201-O

Бренд: OCTO Страницы: 5

Prestige APS-45B

Бренд: Audiovox Страницы: 8

Бренд: Volvo Страницы: 138

Sterling ALL-TERRAIN 576

Бренд: Roadmaster Страницы: 12

Бренд: Raytel LLC Страницы: 40

Бренд: Draw tite Страницы: 4

Бренд: Mercedes-Benz Страницы: 329

Бренд: STO N SHO Страницы: 7

Бренд: Prorack Страницы: 20

Бренд: Fab Fours Страницы: 21

Бренд: AIS Страницы: 2

SANICON TURBO 300

Бренд: Thetford Страницы: 25

Бренд: Lantronix Страницы: 51

Бренд: Subaru Страницы: 44

Бренд: Cadillac Страницы: 20

Бренд: Pyle Страницы: 8

Бренд: Scion Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды