Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 147

background image

CLOCK MODE

WARNING

The clock must be reset any time the battery has been disconnected or

discharged.

1. Turn the key to the ON position. Use the MODE button to toggle to the

odometer display.

2. Press and

hold

the MODE button until the hour segment flashes. Release

the button.

3. With the segment flashing, tap the MODE button to advance to the desired

setting.

4. Press and

hold

the MODE button until the next segment flashes. Release the

button.

5. Repeat steps 3–4 twice to set the 10-minute and 1-minute segments. After

completing the 1-minute segment, step 4 will save the new settings and exit
the clock mode.

6. Turn the key to the OFF position.

ODOMETER/TRIP METER MODE

The odometer displays the total distance traveled by the vehicle. Each trip
odometer displays distance traveled since the trip odometer was reset. To view
the trip odometer, turn the key to the ON position. Use the mode button to toggle
to the trip odometer.

To reset the trip odometer, toggle to the trip odometer, then press and hold the
mode button until the trip odometer resets.

ENGINE ERROR CODES

The error screen displays only when the CHECK ENGINE light is on or when it
goes on and off during one ignition cycle. Error codes are not stored. When the
key is turned OFF, the code and message is lost, but will reappear if the fault
reoccurs after restarting the engine.

If the CHECK ENGINE indicator lamp illuminates, retrieve the error codes from
the display.

1. If the error codes are not displayed, use the MODE button to toggle until “Ck

ENG” displays on the main line of the display.

2. Press and hold the MODE button to enter the diagnostics code menu.

3. Record the numbers displayed in the gear position (if any), clock and

odometer displays.

4. Press the MODE button to advance to the next error code.

29

FEATURES AND CONTROLS

Downloaded from

«
...
29
30
31
32
33
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: Carax Страницы: 2

Бренд: Car-Interface Страницы: 23

Бренд: RuggON Страницы: 2

MOLLE PANELS RAM 2500

Бренд: PUTCO Страницы: 4

Бренд: Westfalia Страницы: 18

Бренд: Hama Страницы: 75

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Бренд: Dakota Digital Страницы: 3

Бренд: Quadratec Страницы: 12

Бренд: AEM Страницы: 27

Бренд: Reese Explore Страницы: 9

Dynamic Power Management Home - Module

Бренд: newmotion Страницы: 20

Escalade 2004 Escalade ESV

Бренд: Cadillac Страницы: 472

Бренд: Master Tailgaters Страницы: 10

Бренд: Westin Страницы: 3

2014 All vehicles

Бренд: Jeep Страницы: 44

Бренд: CaRobotor Страницы: 9

Бренд: VDO Страницы: 6

Бренд: Geo Страницы: 340

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды